Hello,
I have a possible installation on a plot of land where a spring (washhouse) flows along the edge of the parcel. I’d like to know what size my retention basin (flexible tank) should be to allow me to irrigate my crops and especially to cover the peak consumption in summer, knowing that:
- The spring’s flow rate is 0.6 m3 / hour (10 L/minute)
- The average cumulative precipitation is 924 mm/year
- Average monthly ETP = 71 mm
- Maximum monthly ETP = 150 mm
- Areas: 4000 m² PC and 800 m² SA
- Clay-loam soil
- altitude: 420 m
Thanks, community!
Hello, to help you out here’s our data:
- 5,000 m² PC, 2,000 m² SA
- Rainfall approx. 700 mm/year, poorly distributed.
- Coarse sandy-loam soil with clay veins
- Altitude 400 m
- Connected to an irrigation network with a subscription (Canal): 5 m³/h, 6 bar pressure
- Water consumption/year: approx. 3,000 m³
- Winter water consumption without the network, since it’s cut off (November-March): approx. 200 m³
- 200 m³ reserve with a flexible tank, pump connected to it: 10 m³/h, 4.5 bar (cost of tank + earthworks + pump + variable speed drive €15,000)
When we’re connected to the Canal network, we irrigate mainly with the pump and the tank. We refill the tank with water from the Canal. That gives us a much higher irrigation flow rate (double). And combined with the solenoid valves, it really does a great job.
In your case, your source has a very low flow rate; you’d need a full week, 24/7, to fill a 100 m³ tank, for example! The cost of installing a larger tank is much higher than building a reservoir, provided you can remove the soil from your land, otherwise the costs blow up.
In our case, the tank makes it possible to manage the flow rate properly for the high season, but above all to have autonomy in winter so as to avoid pumping from the drinking water network. In a scorching summer, the 200 m³ tank can easily empty in a week, knowing that we can go up to 50 m³/day to manage irrigation rotations with high ETp.
And finally, with ETp around 5 mm at the upper average, you can go up to 30 m³/day just to offset that. I’d advise you to calculate your reserve at at least double your needs at the upper average. And if it’s too expensive, scale it down a bit, but having a safety margin is not a luxury, especially during heatwave episodes like we’ve had in recent years. It would be really frustrating to have a source and not be able to really use it. The goal would be to have a reservoir that fills mainly in winter with at least 3,000 m³ in reserve.
At the Valette garden, the estimate is about 25 m² per day during peak periods. Using this as a reference and assuming there is no rain for 30 days (60 would be ideal).
To size the basin, you first need to calculate the daily deficit:
- Daily requirement: 25 m³
- Water inflow: 15 m³ (your source)
- Daily deficit: 25 m³ – 15 m³ = 10 m³
Over 30 consecutive days, the total deficit would therefore be:
10 m³/day × 30 days = 300 m³
This means the basin must be able to store at least 300 m³ to compensate for this deficit during the peak irrigation period.
But 600 m³ wouldn’t be a luxury.
Several solutions are possible:
- Either create a 600 m³ reserve.
- Or find more water (borehole)
- Or use mains water when you run short.
But in any case, you’ll need to plan for a water reserve of at least 100 m³ to ensure sufficient flow for irrigation. You won’t be able to use the source directly.
Thank you for your very thorough replies.
After discussing with the OUGC, it is permitted to draw only half of a spring’s flow rate, so the tank would fill not at 0.6 m3/h but at 0.3 m3/h.
If this is accepted by the planning authorities (PPRN landslide zoning!), I would therefore store between 800 and 1000 m3 of this water in a flexible tank.
@Sylvain_Couderc I completely understand your focus on the daily deficit of 25 m3 to make up, but I just came across a video you made in 2019 where you present your farm: you explain that your well yields 0.5 m3/hour, i.e. 12 m3/day, and that you built a 150 m3 retention pond. So I’m wondering about the sizing of my reservoir, since my source would give roughly the same flow rate as your well. Do you have another water source that would add to the well’s and therefore allow you to have a smaller reservoir?
@Antoine_Sors Indeed, this video is a bit dated, and I quickly realized I was short on water: my basin was undersized. Today, I have 50 m³ per day thanks to a borehole.
@Sylvain_Couderc How do you arrive at 25m3 per day at peak summer consumption? That’s equivalent to 8mm of water over roughly 3200m2 of crops every day for 30 days, is that right? How many gardens do you water at once?
It probably varies depending on the soil type too, I think — you have sand on the surface; in clay soil, maybe you’d need to irrigate less?
Thanks!
Maybe these details are part of the training in the irrigation focus..?